This video shows the second half of polishing of #2 silver on wood. I start out with abura tokoko, go to 3 different meshes of liquid compound, and they go to ishiko. Step 5 refers to this page, https://zac.wnz.mybluehost.me/website_a640e8d6/?page_id=225
Tag Archives: lacquer based kintsugi
Traditional, lacquer based kintsugi, step 5, initial polishing of silver
This video shows polishing of #2 silver on wood to mesh #3000. It goes from #2000 and then to #3000. To get to the final polish there are about 9 steps to go.
Step 5 refers to this page, https://zac.wnz.mybluehost.me/website_a640e8d6/?page_id=225
Traditional, lacquer based kintsugi, metal finishing, step 3
There is no audio in this video. It shows step #3, second application of jozuri lacquer over silver as a step in the process of finishing graded metal. Step #2 refers to this page, https://zac.wnz.mybluehost.me/website_a640e8d6/?page_id=225
Traditional, lacquer based kintsugi, metal finishing, step 2
There is no audio in this video. It shows step #2, first application of jozuri lacquer over silver as a step in the process of finishing graded metal. Step #2 refers to this page, https://zac.wnz.mybluehost.me/website_a640e8d6/?page_id=225
Traditional, lacquer based kintsugi, step 10
This video has no audio. The step refers to this page, https://zac.wnz.mybluehost.me/website_a640e8d6/?page_id=80
I am applying gold over red. Things to note. I don’t use my wrist to spread the gold, I use a pulling motion with my arm. That is, don’t use your wrist to move the brush, use your whole arm. Also, the technique is to keep your brush at about a 35 degree angle, a little more acute than a 45 degree angle. Then imagine your gold as acting as a mediator between the lacquer and your bristles. Also, I always pull the brush, don’t stab the bristles into the lacquer, it will get lacquer on your bristles and ruin the brush.
Traditional, lacquer based kintsugi, step 9
This video has no audio. The step refers to this page, https://zac.wnz.mybluehost.me/website_a640e8d6/?page_id=80
I am applying red over middle black in preparation for gold. Things to note. This video is about 10 minutes, I continued for about 50 more minutes after thinning and widening the line to the edges. I think let it dry for about 30 minutes in the muro. The first thing I did in preparation for widening and thinning is to run a line of lacquer down the middle of the seam.
Traditional, lacquer based kintsugi, step 6, middle lacquer
This video has no audio. It shows part of step 6, applying middle black lacquer. The whole process took about 1.5 hours.
Traditional, lacquer based kintsugi, step 5a
This video has no audio, it shows step 5a, see https://zac.wnz.mybluehost.me/website_a640e8d6/?page_id=80 , filling a couple of holes in the seam.
For more on traditional, lacquer based kintsugi see kintugi.com
New project, Edo period figure, traditional, lacquer based kintsugi
Here is a very damaged porcelain figurine from the Edo period. I got it because the face is outstanding and I like pieces that have gone through a hard time. The piece has been dropped on its head and had it glued back on, the left hand has been lost, the right foot too. The sleeves of the kimono on both sides have been broken and partially repaired on one side. It will take a long time to get back together.





Traditional, lacquer based kintsugi, reconstruction of missing pieces on Meiji net weights
Application of sabi to fishing net weights to reconstruct missing pieces and fix edge chips on these Meiji era fishing net weights.